Max7 0 Report post Posted February 5, 2007 Akum.. saya baru beli dan stelah cuba configure still tak bleh connect! sbb kalo dulu try configure dari aztech nyer asdl modem ke d-link berjaya.. dan try yang nih tak bleh.. so mintak tolong eh?? Quote Share this post Link to post Share on other sites
xtreme_paranoid 0 Report post Posted February 5, 2007 Akum.. saya baru beli dan stelah cuba configure still tak bleh connect! sbb kalo dulu try configure dari aztech nyer asdl modem ke d-link berjaya.. dan try yang nih tak bleh.. so mintak tolong eh??ko da try reset lom modem tuh?try reset dulu..pastu wat balik step by step mcm biase.. Quote Share this post Link to post Share on other sites
scorps 1 Report post Posted February 5, 2007 Akum.. saya baru beli dan stelah cuba configure still tak bleh connect! sbb kalo dulu try configure dari aztech nyer asdl modem ke d-link berjaya.. dan try yang nih tak bleh.. so mintak tolong eh??apa yg ko dah try buat??cuba citer sikit??apa yg ko baru beli tu??billon ko nak sambung ke dlink ??dlink tu rputer atau swith??ko bagi details bro,baru senang nak tolong... Quote Share this post Link to post Share on other sites
TonikCapGajah2013 175 Report post Posted February 5, 2007 kalao boleh post diagram ... lagi senang En.Scorps nak bantu. Quote Share this post Link to post Share on other sites
prontoxp 2 Report post Posted February 6, 2007 check ip 2 2 device ni... kut kalo sama contohnya 192.168.1.1 mmg tak leh jadi la.. Quote Share this post Link to post Share on other sites
Max7 0 Report post Posted February 6, 2007 Cam nih... saya baru beli wireless router Brand Aztech WL730RT4...sebelum nih pakei adsl2+ modem/router Brand Billion BiPAC 5112S....Sekarang nih saya dah ikut config yang manual bagi tapi still tak leh jadi...config pada billion continous sebelum pakei cable bleh connect.. biler dah connect wireless router Aztech tuh config cam dlm manual hampeh tak jadi..ok nak tanyer skang nih kene pakei ip samer ker??nih ip dier 192.168.1.254.. dua2 router pung samer jerk.. nak pakei PPPoE ker DCHP??caner nih!! tulongg... argh!!! Quote Share this post Link to post Share on other sites
scorps 1 Report post Posted February 6, 2007 (edited) Cam nih... saya baru beli wireless router Brand Aztech WL730RT4...sebelum nih pakei adsl2+ modem/router Brand Billion BiPAC 5112S....Sekarang nih saya dah ikut config yang manual bagi tapi still tak leh jadi...config pada billion continous sebelum pakei cable bleh connect.. biler dah connect wireless router Aztech tuh config cam dlm manual hampeh tak jadi..ok nak tanyer skang nih kene pakei ip samer ker??nih ip dier 192.168.1.254.. dua2 router pung samer jerk.. nak pakei PPPoE ker DCHP??caner nih!! tulongg... argh!!!kan bagus tuu..bagi detailss... ko boleh buat 3 cara,1.jadikan modem ko sebagai brigde mode,dan wifi router ko jadikan sebagai pppoe mode,kiranya ko masukkan username dan password tmnet dalam wifi router tuu..vci=0vpi=35enable nat,aku malas nak translate balik ,aku copy paste dr email tmnet kasi...harap ko paham,Just make sure your bilion is in default mode> (bridge mode) and that will do. There is no setting> required on the bilion>> If you are not sure whether your bilion modem is in> bridge mode or not, simply press and hold the reset> button hole at the back of it for around 10 seconds> while it is power ON to reset it back to> manufacturer default (bridge mode).>> After that, just connect it to the WL730RT4 and> follow the guide given on the WL730RT4 to setting it> up properly. As long as the WL730RT4 is configured> properly, then it will start to connect the bilion> to the internet.>> Also make sure your streamyx account is setup> properly. Make sure the streamyx username is entered> with '@streamyx' at the back. For eg.> userid@streamyxip address dan gateway cara ni ialah ikut wifi router ko,2.cara kedua ialah ko jadikan modem billion ko sebagai router mode(pppoe mode enable),dan pada wifi router ko ko kena enable dhcp server,yg lain cam pppoe mode tak yah on pada wifi router,ip address dan gateway cara ni ialah ikut modem ko,3.cara yg last ialah ko jadikan modem billion ko sebagai router mode(pppoe mode enable),dan ko cucuk cable lan dr modem billion terus ker port lan 1 di wifi router ko,dan port lan2,lan3,dan lan4 tu ko sambung pada komputer,cara ni ko jadikan wifi router tu just sebagai swicth biasa jer..ip address dan gateway cara ni ialah ikut modem ko,pastu pasal setting security pandai2 laa buat..dan aku harap ko paham cara nak buat brigde mode,pppoe mode,harap ko paham dan settle masalah tuu.. Edited February 6, 2007 by scorps Quote Share this post Link to post Share on other sites
Max7 0 Report post Posted February 7, 2007 kan bagus tuu..bagi detailss... ko boleh buat 3 cara,1.jadikan modem ko sebagai brigde mode,dan wifi router ko jadikan sebagai pppoe mode,kiranya ko masukkan username dan password tmnet dalam wifi router tuu..vci=0vpi=35enable nat,aku malas nak translate balik ,aku copy paste dr email tmnet kasi...harap ko paham,Just make sure your bilion is in default mode> (bridge mode) and that will do. There is no setting> required on the bilion>> If you are not sure whether your bilion modem is in> bridge mode or not, simply press and hold the reset> button hole at the back of it for around 10 seconds> while it is power ON to reset it back to> manufacturer default (bridge mode).>> After that, just connect it to the WL730RT4 and> follow the guide given on the WL730RT4 to setting it> up properly. As long as the WL730RT4 is configured> properly, then it will start to connect the bilion> to the internet.>> Also make sure your streamyx account is setup> properly. Make sure the streamyx username is entered> with '@streamyx' at the back. For eg.> userid@streamyxip address dan gateway cara ni ialah ikut wifi router ko,2.cara kedua ialah ko jadikan modem billion ko sebagai router mode(pppoe mode enable),dan pada wifi router ko ko kena enable dhcp server,yg lain cam pppoe mode tak yah on pada wifi router,ip address dan gateway cara ni ialah ikut modem ko,3.cara yg last ialah ko jadikan modem billion ko sebagai router mode(pppoe mode enable),dan ko cucuk cable lan dr modem billion terus ker port lan 1 di wifi router ko,dan port lan2,lan3,dan lan4 tu ko sambung pada komputer,cara ni ko jadikan wifi router tu just sebagai swicth biasa jer..ip address dan gateway cara ni ialah ikut modem ko,pastu pasal setting security pandai2 laa buat..dan aku harap ko paham cara nak buat brigde mode,pppoe mode,harap ko paham dan settle masalah tuu..ok bro.. ianya berjaya... setelah akuh godek mlm tadi.. akuh terpaksa bukak porem omputih tuk tuh sume... ekekkek trimas dia atas bantuan...!! Quote Share this post Link to post Share on other sites
scorps 1 Report post Posted February 7, 2007 ok bro.. ianya berjaya... setelah akuh godek mlm tadi.. akuh terpaksa bukak porem omputih tuk tuh sume... ekekkek trimas dia atas bantuan...!! dah ok takper laa.. Quote Share this post Link to post Share on other sites
emmet 0 Report post Posted March 2, 2007 a'kum...saya pun baru beli wireless baru D-LINK> DI-524...dan guna modem/router BILLION> BIPAC-5112Smasalahnya saya dah congfigure setup wizard untuk wireless tak boleh-boleh juga...dgn guna cara yg scorps ajar pun tak leh..dah reset modem billion tu pun tak boleh2..ada kena yg setting kena buat lagi..takut saya tertggal setting lain ke.. tolong saya ok.. Quote Share this post Link to post Share on other sites
scorps 1 Report post Posted March 2, 2007 a'kum...saya pun baru beli wireless baru D-LINK> DI-524...dan guna modem/router BILLION> BIPAC-5112Smasalahnya saya dah congfigure setup wizard untuk wireless tak boleh-boleh juga...dgn guna cara yg scorps ajar pun tak leh..dah reset modem billion tu pun tak boleh2..ada kena yg setting kena buat lagi..takut saya tertggal setting lain ke.. tolong saya ok..modem ko buat jadi aper??wifi router ko buat jadi aper?? Quote Share this post Link to post Share on other sites
emmet 0 Report post Posted March 3, 2007 modem ko buat jadi aper??wifi router ko buat jadi aper??modem tu aku dah buat jd bridge mode mcm yg ko ajar tu..aku reset factory settingtp yg tukar nievci=0vpi=35enable nat,ada kat dlm setting modem router ja..jd aku tukar kat dlm modem tu lathen aku klik kat bridge mode setting betul ke? atau ada cara lain?dkt wifi lak...aku kena set ke static pppoe atau dynamic pppoe?then bila aku set id streamyx dgn password dkt wifi setting aku punya password akan berubah tak mcm password streamyx.bila aku apply dia punya settingany idea... l Quote Share this post Link to post Share on other sites
scorps 1 Report post Posted March 3, 2007 modem tu aku dah buat jd bridge mode mcm yg ko ajar tu..aku reset factory settingtp yg tukar nievci=0vpi=35enable nat,ada kat dlm setting modem router ja..jd aku tukar kat dlm modem tu lathen aku klik kat bridge mode setting betul ke? atau ada cara lain?dkt wifi lak...aku kena set ke static pppoe atau dynamic pppoe?then bila aku set id streamyx dgn password dkt wifi setting aku punya password akan berubah tak mcm password streamyx.bila aku apply dia punya settingany idea... ldalam modem setting takyah set aper2 bila dah tukar jadi bridge mode,dalam wifi router baru set id ,password streamyx,amik pppoe ,masuk nilai vci,vpi,amik yg pppoe jer.. Quote Share this post Link to post Share on other sites
emmet 0 Report post Posted March 3, 2007 dalam modem setting takyah set aper2 bila dah tukar jadi bridge mode,dalam wifi router baru set id ,password streamyx,amik pppoe ,masuk nilai vci,vpi,amik yg pppoe jer.. tq bro aku dah boleh connect dah...setelah aku godek2 wifi nie dan modem nie..cuma aku nak tanya mcm mana nak buat bila nak connect ke internet kena masuk password dulu..sbb yg nie ko boleh terus masuk ja bila klik kat ie icon...ada ka safetyatau mcm org lain x leh connect walaupun depa leh detect signal wifi aku.. Quote Share this post Link to post Share on other sites
scorps 1 Report post Posted March 3, 2007 (edited) tq bro aku dah boleh connect dah...setelah aku godek2 wifi nie dan modem nie..cuma aku nak tanya mcm mana nak buat bila nak connect ke internet kena masuk password dulu..sbb yg nie ko boleh terus masuk ja bila klik kat ie icon...ada ka safetyatau mcm org lain x leh connect walaupun depa leh detect signal wifi aku..enable kan security ,wep http://my.plains.net/metadot/index.pl?iid=...mp;isa=Category <<rujuk sini,,,WIRELESS SECURITY MEASURESEnable WEPEnabling WEP* (Wired Equivalent Privacy) will require anyone wishing to access the Internet through your wireless network to enter a password. After the correct password is entered, a connection is established, and all data sent from the D-Link to the computer and back is encrypted. From the D-Link configuration screen:1. Click the "Home" tab.2. Click the "Wireless" button.3. Click the "Open System" button next to "Authentication".4. Set the "WEP Encryption" to "128 bit".5. Set the "Key Type" to "ASCII".6. Type a 13 digit password into "Key 1".7. Click "Apply".8. When you connect to your wireless network from a computer, you will need to enter the 13 digit password.*Note: If your computer's operating system supports it, enabling WPA-PSK is more secure than WEP. The steps above can be modified to set up WPA-PSK.Change the SSIDBy default, the D-Link is set to advertise the existence of your wireless network to computers. It does this by broadcasting an SSID (Service Set Identifier), also called a "network name" because it identifies your wireless network. Changing the SSID makes it easier for you to distinguish your network from surrounding networks. From the D-Link configuration screen:1. Click the "Home" tab.2. Click the "Wireless" button.3. Change the "SSID" from "default" to an SSID of your choice.4. Click "Apply". Edited March 5, 2007 by Shanai Quote Share this post Link to post Share on other sites
emmet 0 Report post Posted March 3, 2007 enable kan security ,wep http://my.plains.net/metadot/index.pl?iid=...mp;isa=Category <<rujuk sini,,,WIRELESS SECURITY MEASURESEnable WEPEnabling WEP* (Wired Equivalent Privacy) will require anyone wishing to access the Internet through your wireless network to enter a password. After the correct password is entered, a connection is established, and all data sent from the D-Link to the computer and back is encrypted. From the D-Link configuration screen: 1. Click the "Home" tab. 2. Click the "Wireless" button. 3. Click the "Open System" button next to "Authentication". 4. Set the "WEP Encryption" to "128 bit". 5. Set the "Key Type" to "ASCII". 6. Type a 13 digit password into "Key 1". 7. Click "Apply". 8. When you connect to your wireless network from a computer, you will need to enter the 13 digit password. *Note: If your computer's operating system supports it, enabling WPA-PSK is more secure than WEP. The steps above can be modified to set up WPA-PSK. Change the SSID By default, the D-Link is set to advertise the existence of your wireless network to computers. It does this by broadcasting an SSID (Service Set Identifier), also called a "network name" because it identifies your wireless network. Changing the SSID makes it easier for you to distinguish your network from surrounding networks. From the D-Link configuration screen: 1. Click the "Home" tab. 2. Click the "Wireless" button. 3. Change the "SSID" from "default" to an SSID of your choice. 4. Click "Apply".[ ok aku dah buat...kira skrg dah ada safety la wifi aku..kat dlm modem blh on firewall nak buat ke? Quote Share this post Link to post Share on other sites
scorps 1 Report post Posted March 3, 2007 ikut ko laa..klu nak lagi best pasang jer firewall tuu,, Quote Share this post Link to post Share on other sites
emmet 0 Report post Posted March 4, 2007 ikut ko laa..klu nak lagi best pasang jer firewall tuu,, aku terpikir nak buat bisnes dgn wifi nie,,sbb aku tggal kat kwsn flatnaksewa kat org mcm sebulan rm20 ka..dpt jg buat byr bil bulananada idea tak mcm mana nak setup account utk org yg mggunakan wifi aku..dan berapa ramai yg boleh access dlm satu masa..aku guna streamyx 512 punya.. Quote Share this post Link to post Share on other sites
ideoteque 0 Report post Posted June 11, 2007 Hi,ada soalan skit...rasa2nya..boleh tak pakai modem/router dengna wireless/router?sebab aku try configure macam2 jenis cara..still takleh...I have an Aztech DSL600EU Modem/Router and a wireless broadband router by Aztech WL730RT4..any help will be much appreciated! Quote Share this post Link to post Share on other sites
prontoxp 2 Report post Posted June 11, 2007 Hi,ada soalan skit...rasa2nya..boleh tak pakai modem/router dengna wireless/router?sebab aku try configure macam2 jenis cara..still takleh...I have an Aztech DSL600EU Modem/Router and a wireless broadband router by Aztech WL730RT4..any help will be much appreciated!Tak de masalah asalkan betul cara networkkan device ni... dlm ruangan ni dah beberapa orang yg dah dpt setelkan masalah ni... Quote Share this post Link to post Share on other sites
slaughters 1 Report post Posted June 11, 2007 Hi,ada soalan skit...rasa2nya..boleh tak pakai modem/router dengna wireless/router?sebab aku try configure macam2 jenis cara..still takleh...I have an Aztech DSL600EU Modem/Router and a wireless broadband router by Aztech WL730RT4..any help will be much appreciated!nak pakai dua2 serentak ? better cable dari router ke cable router tu ke LAN. bukan kat WAN. So, wifi router akan bantu sebarkan wireless sahaja. mode AP je tu. Hehehe.. faham ke tak ? mesti tak faham.. dah ade dalam perbincangan sebelum nie.. sat aku lukis..cara nak bagi WAN port tu digunakan.. leceh sket a.. ( sebenarnya aku pening nak terangkan camner ) Hehehe.. Quote Share this post Link to post Share on other sites
prontoxp 2 Report post Posted June 11, 2007 (edited) nak pakai dua2 serentak ? better cable dari router ke cable router tu ke LAN. bukan kat WAN. So, wifi router akan bantu sebarkan wireless sahaja. mode AP je tu. Hehehe.. faham ke tak ? mesti tak faham.. dah ade dalam perbincangan sebelum nie.. sat aku lukis..cara nak bagi WAN port tu digunakan.. leceh sket a.. ( sebenarnya aku pening nak terangkan camner ) Hehehe..Ko kan rajin bagi tutorial... hehehhehe.... bagi aje la .. Edited June 11, 2007 by prontoxp Quote Share this post Link to post Share on other sites
ideoteque 0 Report post Posted June 12, 2007 Helo,Akhirnya berjaya aku buat. macam2 cara. aku set modem/router jadi in Bridge Mode(Aztech punya set up page serabut skit haha), pastu Wireless Router jadi benda ppoe tu. password masuk dalam wireless router. Wow, hebat sungguh gambarrajah! Akan ku kaji utk mendalami pengetahuan... Quote Share this post Link to post Share on other sites
slaughters 1 Report post Posted June 17, 2007 Prontoxp memang pakar dalam melakar gambarajah yang ade kaler2 nie.. Quote Share this post Link to post Share on other sites
aneep79 0 Report post Posted January 15, 2008 nie description modem tu.No computer resource occupation, downstream 24Mbps, upstream 1Mbps, switch able to ADSL2/2+ Routing from WAN to LAN Support 1483 Bridge, PPPoA and PPPoE Support up to 254 simultaneous user Web-based GUI Embedded software for connection status real-time supervision Comply with main DSLAMs Easy Installation with Smart Configuration Tested with All 18 TM DSLAM Lightning Protector Circuit. SIRIM Approved, TM Approved and TM R&D Approved Web-based Configuration and monitoring Software upgradeable Universal Plug and Play (UpPnP) Firewall, IP Filter, Parental Control Quote Share this post Link to post Share on other sites
