sleyer 2 Report post Posted August 29, 2012 aku ade cisco switch 48 port + 4 port sfp [quote] [b] HP 1910-48G Switch (JE009A)[/b] [/quote] [img]http://img694.imageshack.us/img694/7858/switcha.jpg[/img] persoalan aku.. mcm mane aku nak buat sfp port 50 kt bulding B direct link ke port 34 tampa mengangu network2 lain dalam siwtch B? maksudnye aku nak gune sebagai laluan (trunking port je) Quote Share this post Link to post Share on other sites
HelpDesK 11 Report post Posted October 3, 2012 [quote name='sleyer' timestamp='1346223797' post='1084137'] aku ade cisco switch 48 port + 4 port sfp [img]http://img694.imageshack.us/img694/7858/switcha.jpg[/img] persoalan aku.. mcm mane aku nak buat sfp port 50 kt bulding B direct link ke port 34 tampa mengangu network2 lain dalam siwtch B? maksudnye aku nak gune sebagai laluan (trunking port je) [/quote] Boleh buat TAG kat port 34 tu.. Port 50 kat switch B boleh set access vlan x utk semua member switch A as member vlan X dan user dalam switch B default vlan = 1 Buat TAG kat port 50 tu pun boleh jugak tapi kena set access port x kat switch A Firewall kena support tag jugak. Quote Share this post Link to post Share on other sites
sleyer 2 Report post Posted November 28, 2012 leh jelaskan lagi detail tak bro.. aku x berape paham Quote Share this post Link to post Share on other sites
umarzuki 78 Report post Posted December 8, 2012 mungkin bro sleyer boleh cuba dulu CLI-nya kat simulator cisco (tak ingat nama) Quote Share this post Link to post Share on other sites
fendy5479 1 Report post Posted December 15, 2012 dah ada solution ke, bole share? Cisco ke, tp kenapa ada HP model? Quote Share this post Link to post Share on other sites
ridsclan 0 Report post Posted January 31, 2013 biasa aku buat trunk port permit vlan all je ada vlan ke? contoh kalo HP interface GigabitEthernet1/1/1 port link-mode bridge description xxxxx port link-type trunk port trunk permit vlan all kalo cisco interface GigabitEthernet1/0/28 switchport mode trunk dua2 kena port trunk... Quote Share this post Link to post Share on other sites
c0ff33 0 Report post Posted January 18, 2015 (edited) aku ade cisco switch 48 port + 4 port sfp persoalan aku.. mcm mane aku nak buat sfp port 50 kt bulding B direct link ke port 34 tampa mengangu network2 lain dalam siwtch B? maksudnye aku nak gune sebagai laluan (trunking port je) Tak faham sangat soalan. Boleh jelaskan lagi? Ada 2 jenis port je dalam Cisco switch. 1. Access port 2. Trunk port Penjelasan 1. Access port boleh bawak 1 VLAN traffic sahaja 2. Trunk port secara default dia boleh bawak semua VLAN antara switches. Sebab tu ada special tags untuk membezakan aliran traffic samada dari VLAN X atau VLAN Y dsb. Klu ikut diagram ni memang kena buat trunk antara switch. Kena configure 2 2 switch dengan mekanisma yang sama. Klu Cisco switch boleh pilih samada guna ISL atau 802.1Q je Switch#conf t Enter configuration commands, one per line. End with CNTL/Z. Switch(config)#int f0/1 Switch(config-if)#switchport ? access Set access mode characteristics of the interface mode Set trunking mode of the interface native Set trunking native characteristics when interface is in trunking mode nonegotiate Device will not engage in negotiation protocol on this interface port-security Security related command priority Set appliance 802.1p priority trunk Set trunking characteristics of the interface voice Voice appliance attributes <cr> Switch(config-if)# Switch(config-if)#switchport access ? vlan Set VLAN when interface is in access mode Switch(config-if)#switchport access Switch(config-if)#switchport trunk ? allowed Set allowed VLAN characteristics when interface is in trunking mode encapsulation Set trunking encapsulation when interface is in trunking mode native Set trunking native characteristics when interface is in trunking mode Switch(config-if)#switchport trunk Edited January 18, 2015 by c0ff33 Quote Share this post Link to post Share on other sites
