Geekspro 0 Report post Posted October 23, 2007 aku dah pernah buat dulu kat regedit tapi dah tak ingat la cara dia...ade sesape yang ingat tak?? Quote Share this post Link to post Share on other sites
rokhyui 0 Report post Posted October 23, 2007 meh aku bgtauHKEY_LOCAL_MACHINE -> SYSTEM -> CurrentControlSet -> Control -> SessionManager -> MemoryManagement -> PrefetchParameters.kat preftech parameter ubah dari 3 ke 5tapi ada gak dari 2, ubah tkar 5biasa di cut separuh dari asalselamat mencuba Quote Share this post Link to post Share on other sites
zippo 0 Report post Posted October 24, 2007 (edited) When you start up your computer and you are connected to a LAN and your computer is set to DHCP and your computer has to search for the DHCP server and then request and IP address and all other configuration. This process takes up some time and slows down the time it takes to boot the computer up. Following the directions below will help your set a static IP address. Even if your ISP says to use DHCP this tweak may still work for you, but you are warnned!Click Start and click on Run. Type command in the text box and click OK. In DOS, type ipconfig and hit enter. This will show you your current IPs that your NIC and PPPoE adapters have. Only pay attention to your Ethernet Card Adapter, not to the PPP adapter. Next, right click My Network Places and select Properties from the drop down menu. This will open up the Network Connections window. In here, locate your Local Area Network connection and right click it, select Properties from the drop down menu. When the next Window that opens up, select Internet Protocol (TCP/IP) and click Properties at the bottom. In the next window, click 'Use the following IP Address'. This is where that DOS window comes in handy. Copy the same exact IP Address from your Ethernet card (in the dos window) and place it where it says IP Address. Same goes for the Subnet Mask and Default Gateway. If your Default Gateway is blank, then just leave it blank. Click Ok, then Ok again. In the DOS window type exit dos then enter. Reboot your machine. Now there is absolutely NO loading. You can connect as soon as you see your desktop.Quick Note: If you use DHCP (Dynamic IP Address) to connect to the net, you may find that your net connection does not work after this. So if some day your network connection stops working, just go back into the NIC card properties and select automatically get IP address and reboot.Ni cara yg aku dapat. Leh share sama sama kat sini. Edited October 24, 2007 by zippo Quote Share this post Link to post Share on other sites
agas 0 Report post Posted October 24, 2007 Pc aku yg pentium3 punya loading progress bar ade 16 kali.. pakai soft Bootvis tu.. jadi 12 bar je.. ;( Quote Share this post Link to post Share on other sites
MNS 0 Report post Posted October 24, 2007 tengah cuba ni. Kat mana nak dapat informasi asas baerkaitan regedit. wa pernah dengo tapi tak tau fungsi dan cara nak guna. Quote Share this post Link to post Share on other sites
atobey 0 Report post Posted October 24, 2007 meh aku bgtauHKEY_LOCAL_MACHINE -> SYSTEM -> CurrentControlSet -> Control -> SessionManager -> MemoryManagement -> PrefetchParameters.kat preftech parameter ubah dari 3 ke 5tapi ada gak dari 2, ubah tkar 5biasa di cut separuh dari asalselamat mencuba____________________________________________________________________________________oit,tak leh pun..sampai prefetchParameter tu,nak select tang mana...aku select yg tepi2 tu,suma no decimal hapa ntah..tukar kat "EnablePrefetcher" ka? Quote Share this post Link to post Share on other sites
xmatrempit 0 Report post Posted October 25, 2007 (edited) Cuba try test yang ni : Windows XP sahajaControl Panel>Power Options>AdvancedWhen i pressed the power button on my computer - <default> power offTukarkan 'power off' kepada 'hybernate'Tekan on/off power button pc anda. Windows akan hybernate system anda dan terus shutdown. On kan pc anda dan anda akan dapat membuka windows dengan kelajuan cahaya selamat mencuba p/s 1. sekiranya anda shutdown seperti biasa hybernating tidak akan berlaku. ia hanya berlaku sekiranya anda offkan button pc anda secara manual.2. hanya boleh dilakukan oleh sistem atx dan kebanyakkan pc sekarang menggunakan atx power supply. Edited October 25, 2007 by AhliNujum Quote Share this post Link to post Share on other sites
zippo 0 Report post Posted October 25, 2007 meh aku bgtauHKEY_LOCAL_MACHINE -> SYSTEM -> CurrentControlSet -> Control -> SessionManager -> MemoryManagement -> PrefetchParameters.kat preftech parameter ubah dari 3 ke 5tapi ada gak dari 2, ubah tkar 5biasa di cut separuh dari asalselamat mencubaaku ada cuba cara ko, masa nak shut down problem. lambat giler, bila nak on memang laju. memang cam gitu ker ataupun ada conflict yg berlaku? leh terangkan? Quote Share this post Link to post Share on other sites
rokhyui 0 Report post Posted October 25, 2007 tukar kat enable preftech 2 jadi 5aku punya tak puntapi ada cara untuk lajukan shutdown gaknak ker??nak aku leh ajar dalam regedit Quote Share this post Link to post Share on other sites
flizgreen 0 Report post Posted October 25, 2007 lorrr....gtau je la..mesti ader yg nak tau nyerrr..kalo ble lajukan shutdown tur jadik 3saat jerk...kalo startup aku xkesah sgt kalo lambat...sbb aku ske tgk aku nyer boot skin..masa tula nak kasik show off boot skin kt member huhuhuh Quote Share this post Link to post Share on other sites
Geekspro 0 Report post Posted October 25, 2007 Cuba try test yang ni : Windows XP sahajaControl Panel>Power Options>AdvancedWhen i pressed the power button on my computer - <default> power offTukarkan 'power off' kepada 'hybernate'Tekan on/off power button pc anda. Windows akan hybernate system anda dan terus shutdown. On kan pc anda dan anda akan dapat membuka windows dengan kelajuan cahaya selamat mencuba p/s 1. sekiranya anda shutdown seperti biasa hybernating tidak akan berlaku. ia hanya berlaku sekiranya anda offkan button pc anda secara manual.2. hanya boleh dilakukan oleh sistem atx dan kebanyakkan pc sekarang menggunakan atx power supply.Knape kat bahgian yg aku boldkan kat atas kat PC aku x de plak option hybernate ni... Quote Share this post Link to post Share on other sites
qazzaq 0 Report post Posted October 26, 2007 (edited) (xvolution: Knape kat bahgian yg aku boldkan kat atas kat PC aku x de plak option hybernate ni...)Hang kena enable kan dulu fungsi hibernate tu baru dia boleh berfungsi... pegi dekat control panel,amik power option, haa, lepas tu hang cari la dalam tu bab hibernate... Bootvis OK... dan korang boleh jugak cuba try nih,tips yg saya copy dari web mana pun dah lupa... sotak dapat nak bagi credit kat writer dia Do at your own risk, setakat yg saya buat ok aje!Jgn lupa copy paste tips ni, simpan la dlm pendrive korang, senang tak yahnak cari2 lain kali... SO here we go...1. DISABLE INDEXING SERVICESIndexing Services is a small little program that uses large amounts of RAM and can often make a computer endlessly loud and noisy. This system process indexes and updates lists of all the files that are on your computer. It does this so that when you do a search for something on your computer, it will search faster by scanning the index lists. If you don’t search your computer often, or even if you do search often, this system service is completely unnecessary. To disable do the following:1. Go to Start2. Click Settings3. Click Control Panel4. Double-click Add/Remove Programs5. Click the Add/Remove Window Components6. Uncheck the Indexing services7. Click Next 2. OPTIMISE DISPLAY SETTINGSWindows XP can look sexy but displaying all the visual items can waste system resources. To optimise:1. Go to Start2. Click Settings3. Click Control Panel4. Click System5. Click Advanced tab6. In the Performance tab click Settings7. Leave only the following ticked:- Show shadows under menus- Show shadows under mouse pointer- Show translucent selection rectangle- Use drop shadows for icons labels on the desktop- Use visual styles on windows and buttons 3. SPEEDUP FOLDER BROWSINGYou may have noticed that everytime you open my computer to browse folders that there is a slight delay. This is because Windows XP automatically searches for network files and printers everytime you open Windows Explorer. To fix this and to increase browsing significantly:1. Open My Computer2. Click on Tools menu3. Click on Folder Options4. Click on the View tab.5. Uncheck the Automatically search for network folders and printers check box6. Click Apply7. Click Ok8. Reboot your computer 4. IMPROVE MEMORY USAGECacheman Improves the performance of your computer by optimizing the disk cache, memory and a number of other settings.NOTE: This program is shareware and some features require activation.Once Installed:1.Go to Show Wizard and select All2.Run all the wizards by selecting Next or Finished until you are back to the main menu. Use the defaults unless you know exactly what you are doing.3.Exit and Save Cacheman4.Restart Windows 5. OPTIMISE YOUR INTERNET CONNECTIONThere are lots of ways to do this but by far the easiest is to run TCP/IP Optimizer.1. Download and install2. Click the General Settings tab and select your Connection Speed (Kbps)3. Click Network Adapter and choose the interface you use to connect to the Internet4. Check Optimal Settings then Apply5. Reboot 6. OPTIMISE YOUR PAGEFILEIf you give your pagefile a fixed size it saves the operating system from needing to resize the page file.1. Right click on My Computer and select Properties2. Select the Advanced tab3. Under Performance choose the Settings button4. Select the Advanced tab again and under Virtual Memory select Change5. Highlight the drive containing your page file and make the initial Size of the file the same as the Maximum Size of the file.Windows XP sizes the page file to about 1.5X the amount of actual physical memory by default. While this is good for systems with smaller amounts of memory (under 512MB) it is unlikely that a typical XP desktop system will ever need 1.5 X 512MB or more of virtual memory. If you have less than 512MB of memory, leave the page file at its default size. If you have 512MB or more, change the ratio to 1:1 page file size to physical memory size. 7. SPEEDUP FOLDER ACCESS - DISABLE LAST ACCESS UPDATEIf you have a lot of folders and subdirectories on your computer, when you access a directory XP wastes a lot of time updating the time stamp showing the last access time for that directory and for ALL sub directories. To stop XP doing this you need to edit the registry. If you are uncomfortable doing this then please do not attempt. 1. Go to Start and then Run and type “regeditâ€2. Click through the file system until you get to “HKEY_LOCAL_MACHINE\ System\CurrentControlSet\Control\FileSystemâ€3. Right-click in a blank area of the window on the right and select ‘DWORD Value’4. Create a new DWORD Value called ‘NtfsDisableLastAccessUpdate’5. Then Right click on the new value and select ‘Modify’6. Change the Value Data to ‘1′7. Click ‘OK’ 8. MAKE YOUR MENUS LOAD FASTERThis is one of my favourite tweaks as it makes a huge difference to how fast your machine will ‘feel’. What this tweak does is remove the slight delay between clicking on a menu and XP displaying the menu.1. Go to Start then Run2. Type ‘Regedit’ then click ‘Ok’3. Find “HKEY_CURRENT_USER\Control Panel\Desktop\â€4. Select “MenuShowDelayâ€5. Right click and select “Modify’6. Reduce the number to around “100″7. This is the delay time before a menu is opened. You can set it to “0″ but it can make windows really hard to use as menus will open if you just look at them - well move your mouse over them anyway. I tend to go for anywhere between 50-150 depending on my mood 9. IMPROVE XP SHUTDOWN SPEEDThis tweak reduces the time XP waits before automatically closing any running programs when you give it the command to shutdown.1. Go to Start then select Run2. Type ‘Regedit’ and click ok3. Find ‘HKEY_CURRENT_USER\ Control Panel\Desktop\’4. Select ‘WaitToKillAppTimeout’5. Right click and select ‘Modify’6. Change the value to ‘1000′7. Click ‘OK’8. Now select ‘HungAppTimeout’9. Right click and select ‘Modify’10. Change the value to ‘1000′11. Click ‘OK’12. Now find ‘HKEY_USERS\ .DEFAULT\Control Panel\Desktop’13. Select ‘WaitToKillAppTimeout’14. Right click and select ‘Modify’15. Change the value to ‘1000′16. Click ‘OK’17. Now find ‘HKEY_LOCAL_MACHINE\ System\CurrentControlSet\Control\’18. Select ‘WaitToKillServiceTimeout’19. Right click and select ‘Modify’20. Change the value to ‘1000′21. Click ‘OK’ 9. IMPROVE SWAPFILE PERFORMANCEIf you have more than 256MB of RAM this tweak will considerably improve your performance. It basically makes sure that your PC uses every last drop of memory (faster than swap file) before it starts using the swap file.1. Go to Start then Run2. Type “msconfig.exe†then ok3. Click on the System.ini tab4. Expand the 386enh tab by clicking on the plus sign5. Click on new then in the blank box typeâ€ConservativeSwapfileUsage=1″6. Click OK7. Restart PC 10. ENSURE XP IS USING DMA MODEXP enables DMA for Hard-Drives and CD-Roms by default on most ATA or ATAPI (IDE) devices. However, sometimes computers switch to PIO mode which is slower for data transfer - a typical reason is because of a virus. To ensure that your machine is using DMA:1. Open ‘Device Manager’2. Double-click ‘IDE ATA/ATAPI Controllers’3. Right-click ‘Primary Channel’ and select ‘Properties’ and then ‘Advanced Settings’4. In the ‘Current Transfer Mode’ drop-down box, select ‘DMA if Available’ if the current setting is ‘PIO Only’ Edited October 26, 2007 by qazzaq Quote Share this post Link to post Share on other sites
xmatrempit 0 Report post Posted October 26, 2007 Knape kat bahgian yg aku boldkan kat atas kat PC aku x de plak option hybernate ni...Setengah XP setting dia tak sama bukannya Control Panel>Power Options>Advanced>Hybernate tetapi Control Panel>Power Options>Hybernate. Cuba semak balik(help/search - hybernate), kot-kot ada yang terlepas.. Quote Share this post Link to post Share on other sites
TonikCapGajah2013 175 Report post Posted October 26, 2007 tp file nie akan create file kat registry kaa??blh ganggu sistem tk??yerklaa boot login kan bersangkut paut dgn system registry gak...Bootvis ada ubah setting dalam reg file, tapi tak ganggu PC, sebab fungsi dia mengoptimakan boot PC. Ada baiknya buat backup terlebih dahulu.software yg dicadangkan tu compatible tak dgn vista.... home/business/ultimate... ada sesapa pernah cuba.. tq..Tak boleh run dalam Vista. (kalau sapa-sapa ada version untuk vista tolong bagitau)bukan leh ubah jer kat registry keubah kat session manager, memory management, preftech parameter ubah dari 3 ke 5Sebagai tambahan jika cara bootvis masih tidak berkesan boleh guna software lain atau ubah reg. secara manual.Tak ada masalah.Tip yang diberikan oleh qazzaq sebenarnya bukan untuk mempercepatkan loading windowss tetapi untuk mengoptimakan PC ketika menggunakan windows XP. Tip tu OK.10Q Quote Share this post Link to post Share on other sites
rokhyui 0 Report post Posted October 27, 2007 maklumat yg tepat u gazzaqsimpantapi kena pandai gunarisiko tanggung sendiri Quote Share this post Link to post Share on other sites
sandwraith92 0 Report post Posted October 27, 2007 lepas install beley buang kan bende alah nie? Quote Share this post Link to post Share on other sites
zippo 0 Report post Posted October 27, 2007 tukar kat enable preftech 2 jadi 5aku punya tak puntapi ada cara untuk lajukan shutdown gaknak ker??nak aku leh ajar dalam regeditcam mana caranyer? leh kasik step by step? Quote Share this post Link to post Share on other sites
jukiey 0 Report post Posted October 27, 2007 sy telah install dlm win vista, xleh buka. camna nk uninstall ek? aduhhh... Quote Share this post Link to post Share on other sites
TonikCapGajah2013 175 Report post Posted October 27, 2007 kan saya dah beritahu kat atas tu tak boleh run dalam vista.Buka Control Panel > Programs & Features Quote Share this post Link to post Share on other sites
rokhyui 0 Report post Posted November 3, 2007 cam mana caranyer? leh kasik step by step?gazaq ada bgtau dah camana nak shutdown bg laju. tgk balik post erk Quote Share this post Link to post Share on other sites
TonikCapGajah2013 175 Report post Posted November 3, 2007 (edited) satu lagi program yang bagus dan boleh mempercepatkan proses boot:Windows Doctor:http://www.windowsdoctor.com/Download:http://www.windowsdoctor.com/Download.htm Edited November 3, 2007 by PowerRootTongkatAli_GS Quote Share this post Link to post Share on other sites
arashidi 0 Report post Posted November 3, 2007 dah try, ada sikit improvement.. !!! Quote Share this post Link to post Share on other sites
madaya 0 Report post Posted November 3, 2007 klu guna WinASO Registry Optimizer pun bole gak... Quote Share this post Link to post Share on other sites
TonikCapGajah2013 175 Report post Posted November 3, 2007 klu guna WinASO Registry Optimizer pun bole gak...WinASO pun boleh.Kena guna salah satu sebab ada konflik antara WinDoc dengan WinASO Quote Share this post Link to post Share on other sites
Balthazor 1 Report post Posted November 3, 2007 kan saya dah beritahu kat atas tu tak boleh run dalam vista.Buka Control Panel > Programs & Featuresbro..............kalau right click>propeties>Compatibiliti>Win XP x leh ke????????????????????ada satu cara `kejam` caranya 1) Start>RUN2)C:>Windows3)Locate Prefetch folders4)apa yg didalam folder pefetch Folder tuh leh padam Quote Share this post Link to post Share on other sites