verona^worm 0 Report post Posted October 12, 2006 Minta pertolongan...saya baru pakai ubuntu. dual boot dengan windows xp ( dua hardisk) so sekarang ni ada dua problem....1) Tak Boleh nak connect kat internet...2) Thumb drive tak leh detect...minta tolong...pada yang seniorteima kasih Quote Share this post Link to post Share on other sites
sharuzzaman 1 Report post Posted October 15, 2006 soalan no 1 saya tak leh nak jawab.. kena tunggu pengguna ubuntu tolong jawabsoalan no 2:1. apa jenis thumbdrive2. berapa saiz3. kalau boleh, lepas plug-in thumbdrive tu, salin output yang ada dalam /var/log/messages dan tampal kat sini Quote Share this post Link to post Share on other sites
electroboy 3 Report post Posted October 25, 2006 Kalau nak dial naik ke tmnet aku pernah la buat Ubuntu Dapper Drake ada wvdial preinstalled, aku guna yg tu je.Buka terminal, taip#sudo wvdialconfTunggu sehingga modem didetect dgn sempurna, pastu edit file wvdial.conf di /etc, letak nombor dial 1515 pastu masuk username/password.#sudo vi /etc/wvdial.confPastu bila nak dial aku taip je #wvdialKalau streamyx tak pernah plak aku buat. Ko boleh cuba configure interface di System > Administration > Networking. Quote Share this post Link to post Share on other sites
slipars 0 Report post Posted October 25, 2006 (edited) maaf mencelah.. aku newbie dlm linux ni, dah lame pakai windows nih, otak pon dah format windows dah... x tau macam mane nk pakai command2 ni.. aku pakai compaq presario v3000.. masalahnye, mcm mane nk install broadcom wireless nih.. aku ade google care nk install die.. die ckp kene gune ubuntu amd64 generic?? ape bende tu.. ubuntu yg aku nk gune ni ialah ubuntu 6.06 LTS.. mcm mane aku nk tau yg ubuntu aku install tu 32bit @ 64bit ?? pastu gune cabextract ngan ndiswrapper.. ape gune bende tu? aku dh makin pening dah nih.. yg ndiswrapper tu plak mcm dlm format winrar.. wahhh.. byknye nk kene tanye.. ade sape2 bleh tlg ??care yg aku buat skrang..1. Install Ubuntu 6.06 LTS tu2. install bende cabextract..3. copy sp3308.exe ke dekstop..4. pegi kt terminal type cabextract sp3308.exepastu prob.. mane aku nk copy file sp33008.exe tu?pastu yg ndiswrapper tu dlm format tar.gz.. dlm tu ade byk file, aku kene extract dulu ke baru bleh type sudo ndiswrapper -i bcmwl5.inf??ok.. aku dah try care lain pulak..aku type " lspci | grep Broadcom\ Corporation"pastudie kuar "0000:02:0d.0 unknown.... BCM4311(rev 01)" lebih kurang camni la, x igt sgt..pastu aku type"sudo apt-get install bcm43xx-fwcutter" aku buat dua yg bcm43xx tu aku tukar 4311 dan 43xxpastu die tulis".......... , masuk baris ke tiga dia tulis bcm43xx/4311-fwcutter invalid??.." erm, x igt gak. tp file tu die x jumpe.. yg care nih aku ikut kat tutorial ubuntu..nih link die ...http://www.unix-tutorials.com/go.php?id=575wahhh.. camne carenye sebenar nih....TQ Edited October 26, 2006 by slipars Quote Share this post Link to post Share on other sites
farila148 0 Report post Posted November 3, 2006 aku pun sama....guna v3000...tp wireles dia x detct...dah la aku ni pengguna baru dlm linuk..terkebil2 aku cari solution dia...kpd otai2 sekian...harap dapatlah membantu.... Quote Share this post Link to post Share on other sites
TonikCapGajah2013 175 Report post Posted February 16, 2007 mana otai linux ubuntu nie.tak selesai lagi masalah nie. Quote Share this post Link to post Share on other sites
electroboy 3 Report post Posted February 16, 2007 Install ndiswrapper utk wireless eth. Frankly, aku follow je semua yg ada di wiki di link bawah utk jadikan Dapper Drake aku cam PC. So far takde pun masalah. Cuba tgk2 sini dulu:http://ubuntuguide.org/wiki/Dapper Quote Share this post Link to post Share on other sites
athlon_crazy 0 Report post Posted February 16, 2007 (edited) WIFI1) Detect wifi device taip>sudo iwconfigKalau dapat result camnie kat bawah nie, wifi adapter detect.. wlan0 IEEE 802.11g ESSID:"myhome" Mode:Managed Frequency:2.412 GHz Access Point: 60:90:EB:EE:55...bla..bla..bla RTS thr:off Fragment thr=2346 Bkalau xde result taip >sudo lsmod & >sudo dmesg untuk tengok module wifi ada atau tidak & kenal pasti masalah jika ada....kalau xde jugak module wifi, cara terbaik ndiswrapper / cari / gantikan adapter yg support oleh ubuntu(kerja org malas)...2) Check network configuration taip >sudo ifconfig (Jika wifi device tiada masalah)Kalau dapat result cam kat bawah nie, maknanya LAN dah up :lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:102 errors:0 dropped:0 overruns:0 frame:0 TX packets:102 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:7464 (7.2 KiB) TX bytes:7464 (7.2 KiB)wlan0 Link encap:Ethernet HWaddr 00:17:9A:80:90:DD inet6 addr: 192.168.1.13 Mask:255.255.255.0 Broadcast: 255.255.255.255 UP RUNNING MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:12 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:0 (0.0 TX bytes:2736 (2.6 KiB) Base address:0x6000 Kalau ok, maknanya connection internet, dah boleh up...cuma perlu setkan DNS streamyx jika perlu (202.188.0.133 & 202.188.1.5). Tapi kebiasaannya, Ubuntu auto dhcp..x perlu lagi DNS..PPPOE (STREAMYX)-Taip >sudo pppoeconf-masukkan streamyx username & password-masukkan DNS (202.188.0.133 & 202.188.1.5)-Connect during startup? pilih "YES"-Connect now? pilih "YES"-Pastu try la url http://yahoo.com-Taip>pon start connection >poff disconnectKedua dua setting di atas aku apply kat customers2 aku utk Ubuntu Dapper...so far no prob..Harap membantu! Edited February 16, 2007 by athlon_crazy Quote Share this post Link to post Share on other sites
nalsur8 0 Report post Posted March 9, 2007 Minta pertolongan...saya baru pakai ubuntu. dual boot dengan windows xp ( dua hardisk) so sekarang ni ada dua problem....1) Tak Boleh nak connect kat internet...2) Thumb drive tak leh detect...minta tolong...pada yang seniorteima kasihyg pertama sekali nak tanya ko sebelum jwp soklah ko ko guna modem apa? adsl? jenis usb atau nic+router+modemkalu nic+router+modem senang jer...kalu adsl usb modem susah skit banyak keje nak kena buatcompile sana-sini donlod sana-sini... Quote Share this post Link to post Share on other sites
deckerz 0 Report post Posted March 9, 2007 (edited) nih aku nak jawab soalan yang setup tenet kt ubuntu.nih aku citer utk ubuntu 5.10. dialup modem.modem aku cdma.tp rasanya blh gak modem lain.taktau ubuntu lain mcm nih jugak ke.kalu ada yg silap,mintak tolong korang betulkan ek.aku baru belajar.1. tengok kat atas tuh ada System>Administration>networking2. bawah tuh snapshotdah tuh,activate la modem tuh.3.pastu type wvdialconf /etc/wvdial.conf kt terminal,mcm kt bwh nihroot@NAGBOX:/home/ash# wvdialconf /etc/wvdial.cofScanning your serial ports for a modem.ttyS0<*1>: ATQ0 V1 E1 -- failed with 2400 baud, next try: 9600 baudttyS0<*1>: ATQ0 V1 E1 -- failed with 9600 baud, next try: 115200 baudttyS0<*1>: ATQ0 V1 E1 -- OKttyS0<*1>: ATQ0 V1 E1 Z -- OKttyS0<*1>: ATQ0 V1 E1 S0=0 -- OKttyS0<*1>: ATQ0 V1 E1 S0=0 &C1 -- OKttyS0<*1>: ATQ0 V1 E1 S0=0 &C1 &D2 -- OKttyS0<*1>: ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0 -- OKttyS0<*1>: Modem Identifier: ATI -- ERRORttyS0<*1>: Max speed is 115200; that should be safe.ttyS0<*1>: ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0 -- OKPort Scan<*1>: S2 S3 S4 S5 S6 S7 S8 S9Port Scan<*1>: S10 S11 S12 S13 S14 S15 S16 S17Port Scan<*1>: S18 S19 S20 S21 S22 S23 S24 S25Port Scan<*1>: S26 S27 S28 S29 S30 S31 S32 S33Port Scan<*1>: S34 S35 S36 S37 S38 S39 S40 S41Port Scan<*1>: S42 S43 S44 S45 S46 S47 S48 S49Port Scan<*1>: S50 S51 S52 S53Found a modem on /dev/ttyS0.Modem configuration written to /etc/wvdial.cof.ttyS0<Info>: Speed 115200; init "ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0"4. pastu type root@NAGBOX:/home/ash#vi /etc/wvdial.confnanti kuar mcm nih[Dialer Defaults]Modem = /dev/ttyS0Baud = 115200Init1 = ATZInit2 = ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0ISDN = 0Modem Type = Analog Modem; Phone = <Target Phone Number>; Username = <Your Login Name>; Password = <Your Password>~~5. tekan i kalo nk edit file nih.tukar sume2 tuh ikut korang punye username ngan password,phone tuh taruk 1515 lah.jgn lupa buang tanda ; tu.kat [Dialer Defaults] tuh taruklah pape,cth [Dialer tmnet] .Kalau guna cdma mcm aku,taruk kt Init2 tuh mcm nih AT+CMUX=F,1;AT&C2+CRM=135dah siap edit file tuh,tekan Esc,pastu :wq maksud dia nak wite n quit.6.pastu nanti type wvdial tmnettmnet tuh kalo bahagian [Dialer Defaults] tuh korang tukar jadik [Dialer tmnet].paham ek hehhhenanti jadik mcm kt bawahroot@NAGBOX:/etc# wvdial tmnet--> WvDial: Internet dialer version 1.54.0--> Initializing modem.--> Sending: ATZATZOK--> Sending: ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0OK--> Modem initialized.--> Sending: ATDT1515--> Waiting for carrier.ATDT1515NO CARRIER--> No Carrier! Trying again.--> Sending: ATDT1515--> Waiting for carrier.ATDT1515NO CARRIER--> No Carrier! Trying again.--> Sending: ATDT1515--> Waiting for carrier.ATDT1515Caught signal #2! Attempting to exit gracefully...--> Disconnecting at Fri Mar 9 20:42:53 2007root@NAGBOX:/etc# vi wvdial.confroot@NAGBOX:/etc# wvdial tmnet--> WvDial: Internet dialer version 1.54.0--> Initializing modem.--> Sending: ATZATZOK--> Sending: AT+CMUX=F,1;AT&C2+CRM=135AT+CMUX=F,1;AT&C2+CRM=135OK--> Modem initialized.--> Sending: ATDT1515--> Waiting for carrier.ATDT1515CONNECT--> Carrier detected. Waiting for prompt.--> Don't know what to do! Starting pppd and hoping for the best.--> Starting pppd at Fri Mar 9 20:44:21 2007--> pid of pppd: 8260--> Using interface ppp0--> local IP address 172.29.139.49--> remote IP address 172.19.112.21--> primary DNS address 202.188.0.132--> secondary DNS address 202.188.1.5hah tuh tandanya dh connect lah.tuh je aku tau.kalo salah step tuh korang tlg kasik tau ek Edited March 9, 2007 by a5h Quote Share this post Link to post Share on other sites
