Nak Dptkan Internet Dlm Back|track...

[fl1pfl0p 0]

Assalamualaikum...

mcm mana nak configure dsl nak dptkan internet dlm backtrack live cd?.baru jer try backtrack ni,sblum ni gune ubuntu je.Ubuntu live cd boot2 je dh dpt internet tapi backtrack x dpt plak.pc aku behind router and gune streamyx dynamic ip.aku dah try dah command berikut:

ifconfig eth0 up

dhcpcd eth0

pppoe setup --> kuar output 'pppoe: send (send packet) : Network is down'

aku tak paham kenape dier ckp network aku down padahal router dah on dah dan adsl pun tak blinking.Tolong la ye.... aku ni newbie dlm linux ni ...

[FryShadow 90]

set ip dan gateway dah ke?

[fl1pfl0p 0]

set ip dan gateway dah ke?

dah2 tapi lupe nak letak kat atas tadi. aku dah gune command2 berikut:

ifconfig eth0 192.168.1.2 netmask 255.255.255.0

route add default gw 192.168.1.1 eth0

echo nameserver 192.168.1.1 > /etc/resolv.conf

tapi still tak dapat gak..

[sharuzzaman 1]

sebelum ni, ko connect internet dari router ke, dari PC?

maksud aku... ko set sebagai router atau sebagai modem?

kalau sebagai router, ko masuk username dengan password kat web interface router tu... tapi kalau modem, ko masuk username dengan password kat pc

mana satu ko guna?

[fl1pfl0p 0]

aku set sebagai router kot sbb username dan password set dalam router.on komputer jer terus dpt internet.

[sharuzzaman 1]

lepas ko dhcpcd tu, jangan taip pppoe setup.. sebab tu guna untuk dail kalau ko set sebagai modem

lepas ko dhcpcd tu gak.. cuba tail ifconfig dan route -n dan tampal kat sini..

[fl1pfl0p 0]

ok aku dah try dah.aku masuk backtrack aku terus taip command:

1.ifconfig eth0 up

2.ifconfig --> kuar output

eth0 Linkencap:Ethernet HWaddr 00:E0:4D:04:29

inet6 addr:fe80::2e0:4dff:fe04:29ff164 Scope:Link

UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1

RX packets:0 errors:0 dropped:0 overruns:0 frame:0

TX packets:0 errors:0 dropped:0 overruns:0 carrier:0

collisions:0 txqueuelen:0

RX bytes:0 (0.0b) TX bytes:0(0.0b)

Interrupt:10 Base address:0x8000

lo Linkencap:Ethernet HWaddr 00:E0:4D:04:29

inet6 addr:127.0.0.1 Mask:255.0.0.0

UP LOOPBACK RUNNING MULTICAST MTU:16436 Metric:1

RX packets:0 errors:0 dropped:0 overruns:0 frame:0

TX packets:0 errors:0 dropped:0 overruns:0 carrier:0

collisions:0 txqueuelen:0

RX bytes:0 (0.0b) TX bytes:0(0.0b)

3.dhcpcd --> die hang lama

4.ifconfig sekali lagi --> kuar output

lo Linkencap:Ethernet HWaddr 00:E0:4D:04:29 --->eth0 punye dah takde

inet6 addr:127.0.0.1 Mask:255.0.0.0

inet6 addr: ::1/128 Scope:Host

UP LOOPBACK RUNNING MULTICAST MTU:16436 Metric:1

RX packets:0 errors:0 dropped:0 overruns:0 frame:0

TX packets:0 errors:0 dropped:0 overruns:0 carrier:0

collisions:0 txqueuelen:0

RX bytes:0 (0.0b) TX bytes:0(0.0b)

5.route -n ---> kuar output

Kernel IP routing table

Destination Gateway Genmask Flags Metric Ref Use Iface

127.0.0.0 0.0.0.0 255.0.0.0 U 0 0 0 0 lo

Edited September 16, 2007 by fl1pfl0p

[fl1pfl0p 0]

tak de sape ke ade solution tuk problem aku ni.... aku dah puas pikir ni tak dpt lagi.aku dah try cd backtrack tu kat komp office,aku follow setting ip kat xp dapat connect internet tapi kat umah ni tak dapat plak.beza bile aku wat kat umah ngan kat office bile buat dhcpcd command kat umah hang lama tapi buat kat office sekejap je.aku pun penin pikir ape prob die tolong la sape2 yg power linux kat cni...

[sharuzzaman 1]

ko nyer router kat rumah tu tak bagi IP bila ko buat dhcpcd...

ada 2 penyelesaian... pilih salah satu

1. masuk balik dalam interface router ko tu, lepas tu enable dhcp

2. configure network card ko dengan static ip.. eg..

ifconfig eth0 192.168.1.5 netmask 255.255.255.0 gw 192.168.1.1

sila check cara yang tepat... konsepnyer lebih kurang cam tu..

lepas tu ping ko nyer router tu...

[fl1pfl0p 0]

ko nyer router kat rumah tu tak bagi IP bila ko buat dhcpcd...

ada 2 penyelesaian... pilih salah satu

1. masuk balik dalam interface router ko tu, lepas tu enable dhcp

2. configure network card ko dengan static ip.. eg..

ifconfig eth0 192.168.1.5 netmask 255.255.255.0 gw 192.168.1.1

sila check cara yang tepat... konsepnyer lebih kurang cam tu..

lepas tu ping ko nyer router tu...

aku dah cube masuk interface router tu dari xp mmg dah diset sbgi dhcp server tapi dari backtrack tak boleh masuk interface router.Pastu aku pun try command "ifconfig eth0 192.168.1.5 netmask 255.255.255.0 gw 192.168.1.1" output dier ---->gw:Host name look up failure.Pastu ping router pun destination host unreachable.ishh..gatal kepale ku tgk bende ni .dah la aku ni bodo bab networking ni..argh tension.ape2 pun thank u mr sharuzzaman sbb sudi tolong.. .

[athlon_crazy 0]

aku dah cube masuk interface router tu dari xp mmg dah diset sbgi dhcp server tapi dari backtrack tak boleh masuk interface router.Pastu aku pun try command "ifconfig eth0 192.168.1.5 netmask 255.255.255.0 gw 192.168.1.1" output dier ---->gw:Host name look up failure.Pastu ping router pun destination host unreachable.ishh..gatal kepale ku tgk bende ni .dah la aku ni bodo bab networking ni..argh tension.ape2 pun thank u mr sharuzzaman sbb sudi tolong.. .

- Set kan modem router mode balik pastu try

- $ dhcpcd -d -t eth0 10

- check error log ---> /var/log/messages atau /var/log/syslog atau /var/log/dhcpcd.log

[fl1pfl0p 0]

- Set kan modem router mode balik pastu try

- $ dhcpcd -d -t eth0 10

- check error log ---> /var/log/messages atau /var/log/syslog atau /var/log/dhcpcd.log

ok dah try command tu tapi tak boleh tukar jadi "dhcpcd eth0 -d -t 10" baru boleh.tak paham la messages dan syslog tu mcm mane nak check ar?aku ade syslog ngan messages je dhcpcd.log takde. output syslog dier --

Sep 20 23:52:51 (none) kernel: BIOS-e820: 0000000000000000 - 000000000009f800 (usable)

Sep 20 23:52:51 (none) kernel: BIOS-e820: 000000000009f800 - 00000000000a0000 (reserved)

Sep 20 23:52:51 (none) kernel: BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)

Sep 20 23:52:51 (none) kernel: BIOS-e820: 0000000000100000 - 000000001fff0000 (usable)

Sep 20 23:52:51 (none) kernel: BIOS-e820: 000000001fff0000 - 000000001fff3000 (ACPI NVS)

Sep 20 23:52:51 (none) kernel: BIOS-e820: 000000001fff3000 - 0000000020000000 (ACPI data)

Sep 20 23:52:51 (none) kernel: BIOS-e820: 00000000f0000000 - 00000000f4000000 (reserved)

Sep 20 23:52:51 (none) kernel: BIOS-e820: 00000000fec00000 - 0000000100000000 (reserved)

Sep 20 23:52:51 (none) kernel: Allocating PCI resources starting at 30000000 (gap: 20000000:d0000000)

Sep 20 23:52:51 (none) kernel: Built 1 zonelists

Sep 20 23:52:51 (none) kernel: Found and enabled local APIC!

Sep 20 23:52:51 (none) kernel: PID hash table entries: 2048 (order: 11, 32768 bytes)

Sep 20 23:52:51 (none) kernel: Detected 2211.581 MHz processor.

Sep 20 23:52:51 (none) kernel: Console: colour dummy device 80x25

Sep 20 23:52:51 (none) kernel: Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)

Sep 20 23:52:51 (none) kernel: Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)

Sep 20 23:52:51 (none) kernel: Checking if this processor honours the WP bit even in supervisor mode... Ok.

Sep 20 23:52:51 (none) kernel: Calibrating delay using timer specific routine.. 4428.72 BogoMIPS (lpj=8857457)

Sep 20 23:52:51 (none) kernel: Mount-cache hash table entries: 512

Sep 20 23:52:51 (none) kernel: ACPI: setting ELCR to 0200 (from 0c20)

Sep 20 23:52:51 (none) kernel: CPU0: AMD Athlon 64 Processor 3500+ stepping 02

Sep 20 23:52:51 (none) kernel: ACPI: PCI Interrupt Link [LNK1] (IRQs 5 7 9 10 11 14 15) *0, disabled.

Sep 20 23:52:51 (none) kernel: ACPI: PCI Interrupt Link [LNK2] (IRQs 5 7 9 10 11 14 15) *0, disabled.

Sep 20 23:52:51 (none) kernel: ACPI: PCI Interrupt Link [LNK3] (IRQs 5 7 9 10 11 14 15) *0, disabled.

Sep 20 23:52:51 (none) kernel: ACPI: PCI Interrupt Link [LNK4] (IRQs 5 7 9 10 11 14 15) *0, disabled.

Sep 20 23:52:51 (none) kernel: ACPI: PCI Interrupt Link [LNK5] (IRQs 5 7 9 10 11 14 15) *0, disabled.

Sep 20 23:52:51 (none) kernel: ACPI: PCI Interrupt Link [LNK6] (IRQs *5 7 9 10 11 14 15)

Sep 20 23:52:51 (none) kernel: ACPI: PCI Interrupt Link [LNK7] (IRQs 5 7 9 10 11 14 15) *0, disabled.

Sep 20 23:52:51 (none) kernel: ACPI: PCI Interrupt Link [LNK8] (IRQs 5 7 9 10 11 14 15) *0, disabled.

Sep 20 23:52:51 (none) kernel: ACPI: PCI Interrupt Link [LP2P] (IRQs 5 7 9 10 11 14 15) *0, disabled.

Sep 20 23:52:51 (none) kernel: ACPI: PCI Interrupt Link [LUBA] (IRQs 5 7 9 *10 11 14 15)

Sep 20 23:52:51 (none) kernel: ACPI: PCI Interrupt Link [LMAC] (IRQs 5 7 9 *10 11 14 15)

Sep 20 23:52:51 (none) kernel: ACPI: PCI Interrupt Link [LAZA] (IRQs 5 7 9 10 *11 14 15)

Sep 20 23:52:51 (none) kernel: ACPI: PCI Interrupt Link [LPMU] (IRQs *5 7 9 10 11 14 15)

Sep 20 23:52:51 (none) kernel: ACPI: PCI Interrupt Link [LSMB] (IRQs *5 7 9 10 11 14 15)

Sep 20 23:52:51 (none) kernel: ACPI: PCI Interrupt Link [LUB2] (IRQs 5 7 9 10 *11 14 15)

Sep 20 23:52:51 (none) kernel: ACPI: PCI Interrupt Link [LIDE] (IRQs 5 7 9 10 11 14 15) *0, disabled.

Sep 20 23:52:51 (none) kernel: ACPI: PCI Interrupt Link [LSID] (IRQs 5 7 9 10 *11 14 15)

Sep 20 23:52:51 (none) kernel: ACPI: PCI Interrupt Link [LFID] (IRQs 5 7 9 *10 11 14 15)

Sep 20 23:52:51 (none) kernel: ACPI: PCI Interrupt Link [APC1] (IRQs 16) *0, disabled.

Sep 20 23:52:51 (none) kernel: ACPI: PCI Interrupt Link [APC2] (IRQs 17) *0, disabled.

Sep 20 23:52:51 (none) kernel: ACPI: PCI Interrupt Link [APC3] (IRQs 18) *0, disabled.

Sep 20 23:52:51 (none) kernel: ACPI: PCI Interrupt Link [APC4] (IRQs 19) *0, disabled.

Sep 20 23:52:51 (none) kernel: ACPI: PCI Interrupt Link [APC5] (IRQs 16) *0, disabled.

Sep 20 23:52:51 (none) kernel: ACPI: PCI Interrupt Link [APC6] (IRQs 16) *0, disabled.

Sep 20 23:52:51 (none) kernel: ACPI: PCI Interrupt Link [APC7] (IRQs 16) *0, disabled.

Sep 20 23:52:51 (none) kernel: ACPI: PCI Interrupt Link [APC8] (IRQs 16) *0, disabled.

Sep 20 23:52:51 (none) kernel: ACPI: PCI Interrupt Link [APCF] (IRQs 20 21 22 23) *0, disabled.

Sep 20 23:52:51 (none) kernel: ACPI: PCI Interrupt Link [APCH] (IRQs 20 21 22 23) *0, disabled.

Sep 20 23:52:51 (none) kernel: ACPI: PCI Interrupt Link [APMU] (IRQs 20 21 22 23) *0, disabled.

Sep 20 23:52:51 (none) kernel: ACPI: PCI Interrupt Link [AAZA] (IRQs 20 21 22 23) *0, disabled.

Sep 20 23:52:51 (none) kernel: ACPI: PCI Interrupt Link [APCS] (IRQs 20 21 22 23) *0, disabled.

Sep 20 23:52:51 (none) kernel: ACPI: PCI Interrupt Link [APCL] (IRQs 20 21 22 23) *0, disabled.

Sep 20 23:52:51 (none) kernel: ACPI: PCI Interrupt Link [APCM] (IRQs 20 21 22 23) *0, disabled.

Sep 20 23:52:51 (none) kernel: ACPI: PCI Interrupt Link [APCZ] (IRQs 20 21 22 23) *0, disabled.

Sep 20 23:52:51 (none) kernel: ACPI: PCI Interrupt Link [APSI] (IRQs 20 21 22 23) *0, disabled.

Sep 20 23:52:51 (none) kernel: ACPI: PCI Interrupt Link [APSJ] (IRQs 20 21 22 23) *0, disabled.

Sep 20 23:52:51 (none) kernel: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)

Sep 20 23:52:51 (none) kernel: pcie_portdrv_probe->Dev[0374:10de] has invalid IRQ. Check vendor BIOS

Sep 20 23:52:51 (none) kernel: assign_interrupt_mode Found MSI capability

Sep 20 23:52:51 (none) kernel: pcie_portdrv_probe->Dev[0374:10de] has invalid IRQ. Check vendor BIOS

Sep 20 23:52:51 (none) kernel: assign_interrupt_mode Found MSI capability

Sep 20 23:52:51 (none) kernel: pcie_portdrv_probe->Dev[0378:10de] has invalid IRQ. Check vendor BIOS

Sep 20 23:52:51 (none) kernel: assign_interrupt_mode Found MSI capability

Sep 20 23:52:51 (none) kernel: pcie_portdrv_probe->Dev[0375:10de] has invalid IRQ. Check vendor BIOS

Sep 20 23:52:51 (none) kernel: assign_interrupt_mode Found MSI capability

Sep 20 23:52:51 (none) kernel: pcie_portdrv_probe->Dev[0377:10de] has invalid IRQ. Check vendor BIOS

Sep 20 23:52:51 (none) kernel: assign_interrupt_mode Found MSI capability

Sep 20 23:52:51 (none) kernel: vesafb: Mode is VGA compatible

Sep 20 23:52:51 (none) kernel: Console: switching to colour frame buffer device 128x48

Sep 20 23:52:51 (none) kernel: RAMDISK driver initialized: 16 RAM disks of 4444K size 1024 blocksize

Sep 20 23:52:51 (none) kernel: Compaq SMART2 Driver (v 2.6.0)

Sep 20 23:52:51 (none) kernel: NFORCE-MCP55: BIOS didn't set cable bits correctly. Enabling workaround.

Sep 20 23:52:51 (none) kernel: hda: DVD DC DW1670, ATAPI CD/DVD-ROM drive

Sep 20 23:52:51 (none) kernel: ide0 at 0x1f0-0x1f7,0x3f6 on irq 14

Sep 20 23:52:51 (none) kernel: ide-floppy driver 0.99.newide

Sep 20 23:52:51 (none) kernel: Loading Adaptec I2O RAID: Version 2.4 Build 5go

Sep 20 23:52:51 (none) kernel: scsi: <fdomain> Detection failed (no card)

Sep 20 23:52:51 (none) kernel: Emulex LightPulse Fibre Channel SCSI driver 8.1.0

Sep 20 23:52:51 (none) kernel: Copyright© 2004-2005 Emulex. All rights reserved.

Sep 20 23:52:51 (none) kernel: Failed initialization of WD-7000 SCSI card!

Sep 20 23:52:51 (none) kernel: GDT-HA: Storage RAID Controller Driver. Version: 3.04

Sep 20 23:52:51 (none) kernel: GDT-HA: Found 0 PCI Storage RAID Controllers

Sep 20 23:52:51 (none) kernel: 3ware Storage Controller device driver for Linux v1.26.02.001.

Sep 20 23:52:51 (none) kernel: 3ware 9000 Storage Controller device driver for Linux v2.26.02.004.

Sep 20 23:52:51 (none) kernel: ACPI: PCI Interrupt Link [LSID] enabled at IRQ 11

Sep 20 23:52:51 (none) kernel: PCI: setting IRQ 11 as level-triggered

Sep 20 23:52:51 (none) kernel: ACPI: PCI Interrupt Link [LFID] enabled at IRQ 10

Sep 20 23:52:51 (none) kernel: PCI: setting IRQ 10 as level-triggered

Sep 20 23:52:51 (none) kernel: IP route cache hash table entries: 8192 (order: 3, 32768 bytes)

Sep 20 23:52:51 (none) kernel: TCP established hash table entries: 32768 (order: 6, 262144 bytes)

Sep 20 23:52:51 (none) kernel: TCP bind hash table entries: 32768 (order: 6, 262144 bytes)

Sep 20 23:52:51 (none) kernel: Using IPI Shortcut mode

Sep 20 23:52:51 (none) kernel: VFS: Mounted root (ext2 filesystem).

Sep 20 23:52:51 (none) kernel: Registering unionfs 1.1.3

Sep 20 23:52:52 (none) cardmgr[3069]: no sockets found!

Sep 20 23:52:53 (none) kernel: ACPI: PCI Interrupt Link [LMAC] enabled at IRQ 10

Sep 20 23:52:54 (none) kernel: ACPI: PCI Interrupt Link [LAZA] enabled at IRQ 11

Sep 20 23:52:56 (none) kernel: ACPI: PCI Interrupt Link [LUB2] enabled at IRQ 11

Sep 20 23:52:56 (none) kernel: ACPI: PCI Interrupt Link [LUBA] enabled at IRQ 10

Sep 20 23:53:41 (none) dhcpcd[5301]: timed out waiting for a valid DHCP server response

Sep 20 23:55:16 (none) kernel: Bad page state at free_hot_cold_page (in process 'artsd', page c139fc20)------

Sep 20 23:55:16 (none) kernel: flags:0x80000414 mapping:00000000 mapcount:0 count:0 |

Sep 20 23:55:16 (none) kernel: Backtrace: |

Sep 20 23:55:16 (none) kernel: [<c0136dc6>] bad_page+0x5c/0x92 |

Sep 20 23:55:16 (none) kernel: [<c01374d4>] free_hot_cold_page+0x58/0xe5 |

Sep 20 23:55:16 (none) kernel: [<c013fe85>] zap_pte_range+0x17d/0x241 |

Sep 20 23:55:16 (none) kernel: [<c013fff0>] unmap_page_range+0xa7/0xf1 |--->dier ulang rangkap ni 15 kali

Sep 20 23:55:16 (none) kernel: [<c0140113>] unmap_vmas+0xd9/0x1be |

Sep 20 23:55:16 (none) kernel: [<c0143746>] unmap_region+0x8f/0xfa |

Sep 20 23:55:16 (none) kernel: [<c01439c5>] do_munmap+0xd5/0xeb |

Sep 20 23:55:16 (none) kernel: [<c0143a0d>] sys_munmap+0x32/0x4d |

Sep 20 23:55:16 (none) kernel: [<c01027f9>] syscall_call+0x7/0xb |

Sep 20 23:55:16 (none) kernel: Trying to fix it up, but a reboot is needed ------|

Sep 21 00:02:56 (none) kernel: sdb: assuming drive cache: write through

Sep 21 00:02:56 (none) kernel: sdb: assuming drive cache: write through

Sep 21 00:11:01 (none) dhcpcd[10639]: timed out waiting for a valid DHCP server response

Sep 21 00:12:51 (none) dhcpcd[11210]: timed out waiting for a valid DHCP server response

pastu messages plak:--

May 25 20:16:13 (none) kernel: NET: Registered protocol family 10

May 25 20:16:13 (none) kernel: lo: Disabled Privacy Extensions

May 25 20:16:13 (none) kernel: IPv6 over IPv4 tunneling driver

May 25 20:16:35 (none) gconfd (root-4253): starting (version 2.6.2), pid 4253 user 'root'

May 25 20:16:35 (none) gconfd (root-4253): Resolved address "xml:readonly:/etc/gconf/gconf.xml.mandatory" to a read-only config source at position 0

May 25 20:16:35 (none) gconfd (root-4253): Resolved address "xml:readwrite:/root/.gconf" to a writable config source at position 1

May 25 20:16:35 (none) gconfd (root-4253): Resolved address "xml:readonly:/etc/gconf/gconf.xml.defaults" to a read-only config source at position 2

May 25 20:16:43 (none) kernel: ADDRCONF(NETDEV_UP): eth1: link is not ready

May 25 20:16:44 (none) kernel: tg3: eth1: Link is up at 100 Mbps, full duplex.

May 25 20:16:44 (none) kernel: tg3: eth1: Flow control is off for TX and off for RX.

May 25 20:16:44 (none) kernel: ADDRCONF(NETDEV_CHANGE): eth1: link becomes ready

May 25 20:19:35 (none) gconfd (root-4253): GConf server is not in use, shutting down.

May 25 20:19:35 (none) gconfd (root-4253): Exiting

May 25 20:31:54 (none) -- MARK --

Sep 20 23:52:50 (none) syslogd 1.4.1: restart.

Sep 20 23:52:51 (none) kernel: klogd 1.4.1, log source = /proc/kmsg started.

Sep 20 23:52:51 (none) kernel: Linux version 2.6.15.6 (root@slax) (gcc version 3.3.5) #1 SMP Fri Mar 24 16:46:23 GMT 2006

Sep 20 23:52:51 (none) kernel: BIOS-provided physical RAM map:

Sep 20 23:52:51 (none) kernel: 0MB HIGHMEM available.

Sep 20 23:52:51 (none) kernel: 511MB LOWMEM available.

Sep 20 23:52:51 (none) kernel: DMI 2.2 present.

Sep 20 23:52:51 (none) kernel: ACPI: PM-Timer IO Port: 0x1008

Sep 20 23:52:51 (none) kernel: Kernel command line: max_loop=255 initrd=boot/initrd.gz vga=0x317 init=linuxrc load_ramdisk=1 prompt_ramdisk=0 ramdisk_size=4444 root=/dev/ram0 rw BOOT_IMAGE=boot/vmlinuz

Sep 20 23:52:51 (none) kernel: Initializing CPU#0

Sep 20 23:52:51 (none) kernel: Using pmtmr for high-res timesource

Sep 20 23:52:51 (none) kernel: Memory: 510376k/524224k available (3702k kernel code, 13196k reserved, 1995k data, 280k init, 0k highmem)

Sep 20 23:52:51 (none) kernel: CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)

Sep 20 23:52:51 (none) kernel: CPU: L2 Cache: 512K (64 bytes/line)

Sep 20 23:52:51 (none) kernel: Intel machine check architecture supported.

Sep 20 23:52:51 (none) kernel: Intel machine check reporting enabled on CPU#0.

Sep 20 23:52:51 (none) kernel: mtrr: v2.0 (20020519)

Sep 20 23:52:51 (none) kernel: Enabling fast FPU save and restore... done.

Sep 20 23:52:51 (none) kernel: Enabling unmasked SIMD FPU exception support... done.

Sep 20 23:52:51 (none) kernel: Checking 'hlt' instruction... OK.

Sep 20 23:52:51 (none) kernel: SMP motherboard not detected.

Sep 20 23:52:51 (none) kernel: Brought up 1 CPUs

Sep 20 23:52:51 (none) kernel: checking if image is initramfs...it isn't (no cpio magic); looks like an initrd

Sep 20 23:52:51 (none) kernel: Freeing initrd memory: 1669k freed

Sep 20 23:52:51 (none) kernel: NET: Registered protocol family 16

Sep 20 23:52:51 (none) kernel: ACPI: bus type pci registered

Sep 20 23:52:51 (none) kernel: PCI: PCI BIOS revision 3.00 entry at 0xfab00, last bus=6

Sep 20 23:52:51 (none) kernel: PCI: Using MMCONFIG

Sep 20 23:52:51 (none) kernel: ACPI: Subsystem revision 20050902

Sep 20 23:52:51 (none) kernel: ACPI: Interpreter enabled

Sep 20 23:52:51 (none) kernel: ACPI: Using PIC for interrupt routing

Sep 20 23:52:51 (none) kernel: ACPI: PCI Root Bridge [PCI0] (0000:00)

Sep 20 23:52:51 (none) kernel: PCI: Transparent bridge - 0000:00:06.0

Sep 20 23:52:51 (none) kernel: Linux Plug and Play Support v0.97 © Adam Belay

Sep 20 23:52:51 (none) kernel: SCSI subsystem initialized

Sep 20 23:52:51 (none) kernel: usbcore: registered new driver usbfs

Sep 20 23:52:51 (none) kernel: usbcore: registered new driver hub

Sep 20 23:52:51 (none) kernel: PCI: Using ACPI for IRQ routing

Sep 20 23:52:51 (none) kernel: PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report

Sep 20 23:52:51 (none) kernel: PCI: Bridge: 0000:00:06.0

Sep 20 23:52:51 (none) kernel: IO window: b000-bfff

Sep 20 23:52:51 (none) kernel: MEM window: fde00000-fdefffff

Sep 20 23:52:51 (none) kernel: PREFETCH window: fdd00000-fddfffff

Sep 20 23:52:51 (none) kernel: PCI: Bridge: 0000:00:0b.0

Sep 20 23:52:51 (none) kernel: IO window: a000-afff

Sep 20 23:52:51 (none) kernel: MEM window: fdc00000-fdcfffff

Sep 20 23:52:51 (none) kernel: PREFETCH window: fdb00000-fdbfffff

Sep 20 23:52:51 (none) kernel: PCI: Bridge: 0000:00:0c.0

Sep 20 23:52:51 (none) kernel: IO window: 9000-9fff

Sep 20 23:52:51 (none) kernel: MEM window: fda00000-fdafffff

Sep 20 23:52:51 (none) kernel: PREFETCH window: fd900000-fd9fffff

Sep 20 23:52:51 (none) kernel: PCI: Bridge: 0000:00:0d.0

Sep 20 23:52:51 (none) kernel: IO window: 8000-8fff

Sep 20 23:52:51 (none) kernel: MEM window: fd800000-fd8fffff

Sep 20 23:52:51 (none) kernel: PREFETCH window: fd700000-fd7fffff

Sep 20 23:52:51 (none) kernel: PCI: Bridge: 0000:00:0e.0

Sep 20 23:52:51 (none) kernel: IO window: 7000-7fff

Sep 20 23:52:51 (none) kernel: MEM window: fd600000-fd6fffff

Sep 20 23:52:51 (none) kernel: PREFETCH window: fd500000-fd5fffff

Sep 20 23:52:51 (none) kernel: PCI: Bridge: 0000:00:0f.0

Sep 20 23:52:51 (none) kernel: IO window: 6000-6fff

Sep 20 23:52:51 (none) kernel: MEM window: fd400000-fd4fffff

Sep 20 23:52:51 (none) kernel: PREFETCH window: e8000000-efffffff

Sep 20 23:52:51 (none) kernel: apm: BIOS version 1.2 Flags 0x07 (Driver version 1.16ac)

Sep 20 23:52:51 (none) kernel: apm: overridden by ACPI.

Sep 20 23:52:51 (none) kernel: VFS: Disk quotas dquot_6.5.1

Sep 20 23:52:51 (none) kernel: NTFS driver 2.1.25 [Flags: R/W].

Sep 20 23:52:51 (none) kernel: JFS: nTxBlock = 4002, nTxLock = 32019

Sep 20 23:52:51 (none) kernel: SGI XFS with ACLs, security attributes, large block numbers, no debug enabled

Sep 20 23:52:51 (none) kernel: SGI XFS Quota Management subsystem

Sep 20 23:52:51 (none) kernel: Initializing Cryptographic API

Sep 20 23:52:51 (none) kernel: io scheduler noop registered

Sep 20 23:52:51 (none) kernel: io scheduler anticipatory registered

Sep 20 23:52:51 (none) kernel: io scheduler deadline registered

Sep 20 23:52:51 (none) kernel: io scheduler cfq registered

Sep 20 23:52:51 (none) kernel: pci_hotplug: PCI Hot Plug PCI Core version: 0.5

Sep 20 23:52:51 (none) kernel: vesafb: framebuffer at 0xe8000000, mapped to 0xe0a80000, using 6144k, total 16384k

Sep 20 23:52:51 (none) kernel: vesafb: mode is 1024x768x16, linelength=2048, pages=9

Sep 20 23:52:51 (none) kernel: vesafb: protected mode interface info at c000:58c2

Sep 20 23:52:51 (none) kernel: vesafb: scrolling: redraw

Sep 20 23:52:51 (none) kernel: vesafb: Truecolor: size=0:5:6:5, shift=0:11:5:0

Sep 20 23:52:51 (none) kernel: bootsplash 3.1.6-2004/03/31: looking for picture...<6>...no good signature found.

Sep 20 23:52:51 (none) kernel: fb0: VESA VGA frame buffer device

Sep 20 23:52:51 (none) kernel: ACPI: Power Button (FF) [PWRF]

Sep 20 23:52:51 (none) kernel: ACPI: Power Button (CM) [PWRB]

Sep 20 23:52:51 (none) kernel: ACPI: Sleep Button (CM) [sLPB]

Sep 20 23:52:51 (none) kernel: ACPI: Fan [FAN] (on)

Sep 20 23:52:51 (none) kernel: ACPI: Thermal Zone [THRM] (40 C)

Sep 20 23:52:51 (none) kernel: isapnp: Scanning for PnP cards...

Sep 20 23:52:51 (none) kernel: isapnp: No Plug & Play device found

Sep 20 23:52:51 (none) kernel: Real Time Clock Driver v1.12

Sep 20 23:52:51 (none) kernel: PNP: No PS/2 controller found. Probing ports directly.

Sep 20 23:52:51 (none) kernel: serio: i8042 AUX port at 0x60,0x64 irq 12

Sep 20 23:52:51 (none) kernel: serio: i8042 KBD port at 0x60,0x64 irq 1

Sep 20 23:52:51 (none) kernel: Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled

Sep 20 23:52:51 (none) kernel: serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A

Sep 20 23:52:51 (none) kernel: Floppy drive(s): fd0 is 1.44M

Sep 20 23:52:51 (none) kernel: FDC 0 is a post-1991 82077

Sep 20 23:52:51 (none) kernel: loop: loaded (max 255 devices)

Sep 20 23:52:51 (none) kernel: HP CISS Driver (v 2.6.8)

Sep 20 23:52:51 (none) kernel: Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2

Sep 20 23:52:51 (none) kernel: ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx

Sep 20 23:52:51 (none) kernel: NFORCE-MCP55: IDE controller at PCI slot 0000:00:04.0

Sep 20 23:52:51 (none) kernel: NFORCE-MCP55: chipset revision 161

Sep 20 23:52:51 (none) kernel: NFORCE-MCP55: not 100%% native mode: will probe irqs later

Sep 20 23:52:51 (none) kernel: NFORCE-MCP55: 0000:00:04.0 (rev a1) UDMA133 controller

Sep 20 23:52:51 (none) kernel: ide0: BM-DMA at 0xf400-0xf407, BIOS settings: hda:DMA, hdb:DMA

Sep 20 23:52:51 (none) kernel: hda: ATAPI 48X DVD-ROM DVD-R-RAM CD-R/RW drive, 2048kB Cache, UDMA(66)

Sep 20 23:52:51 (none) kernel: Uniform CD-ROM driver Revision: 3.20

Sep 20 23:52:51 (none) kernel: Detecting Adaptec I2O RAID controllers...

Sep 20 23:52:51 (none) kernel: Adaptec aacraid driver (1.1-4 Mar 24 2006 16:42:55)

Sep 20 23:52:51 (none) kernel: sym53c416.c: Version 1.0.0-ac

Sep 20 23:52:51 (none) kernel: qlogicfas: no cards were found, please specify I/O address and IRQ using iobase= and irq= options<6>QLogic Fibre Channel HBA Driver

Sep 20 23:52:51 (none) kernel: megaraid cmm: 2.20.2.6 (Release Date: Mon Mar 7 00:01:03 EST 2005)

Sep 20 23:52:51 (none) kernel: megaraid: 2.20.4.6 (Release Date: Mon Mar 07 12:27:22 EST 2005)

Sep 20 23:52:51 (none) kernel: megasas: 00.00.02.00-rc4 Fri Sep 16 12:37:08 EDT 2005

Sep 20 23:52:51 (none) kernel: nsp32: loading...

Sep 20 23:52:51 (none) kernel: ipr: IBM Power RAID SCSI Device Driver version: 2.1.0 (October 31, 2005)

Sep 20 23:52:51 (none) kernel: ACPI: PCI Interrupt 0000:00:05.0[A] -> Link [LSID] -> GSI 11 (level, low) -> IRQ 11

Sep 20 23:52:51 (none) kernel: ata1: SATA max UDMA/133 cmd 0x9F0 ctl 0xBF2 bmdma 0xE000 irq 11

Sep 20 23:52:51 (none) kernel: ata2: SATA max UDMA/133 cmd 0x970 ctl 0xB72 bmdma 0xE008 irq 11

Sep 20 23:52:51 (none) kernel: ata1: dev 0 ATA-7, max UDMA/133, 160836480 sectors: LBA48

Sep 20 23:52:51 (none) kernel: ata1: dev 0 configured for UDMA/133

Sep 20 23:52:51 (none) kernel: scsi2 : sata_nv

Sep 20 23:52:51 (none) kernel: ata2: no device found (phy stat 00000000)

Sep 20 23:52:51 (none) kernel: scsi3 : sata_nv

Sep 20 23:52:51 (none) kernel: Vendor: ATA Model: HDS728080PLA380 Rev: PF2O

Sep 20 23:52:51 (none) kernel: Type: Direct-Access ANSI SCSI revision: 05

Sep 20 23:52:51 (none) kernel: ACPI: PCI Interrupt 0000:00:05.1 -> Link [LFID] -> GSI 10 (level, low) -> IRQ 10

Sep 20 23:52:51 (none) kernel: ata3: SATA max UDMA/133 cmd 0x9E0 ctl 0xBE2 bmdma 0xCC00 irq 10

Sep 20 23:52:51 (none) kernel: ata4: SATA max UDMA/133 cmd 0x960 ctl 0xB62 bmdma 0xCC08 irq 10

Sep 20 23:52:51 (none) kernel: ata3: no device found (phy stat 00000000)

Sep 20 23:52:51 (none) kernel: scsi4 : sata_nv

Sep 20 23:52:51 (none) kernel: ata4: no device found (phy stat 00000000)

Sep 20 23:52:51 (none) kernel: scsi5 : sata_nv

Sep 20 23:52:51 (none) kernel: SCSI device sda: 160836480 512-byte hdwr sectors (82348 MB)

Sep 20 23:52:51 (none) kernel: SCSI device sda: drive cache: write back

Sep 20 23:52:51 (none) kernel: SCSI device sda: 160836480 512-byte hdwr sectors (82348 MB)

Sep 20 23:52:51 (none) kernel: SCSI device sda: drive cache: write back

Sep 20 23:52:51 (none) kernel: sda: sda1 sda2 < sda5 >

Sep 20 23:52:51 (none) kernel: sd 2:0:0:0: Attached scsi disk sda

Sep 20 23:52:51 (none) kernel: I2O subsystem v1.288

Sep 20 23:52:51 (none) kernel: i2o: max drivers = 8

Sep 20 23:52:51 (none) kernel: I2O Configuration OSM v1.248

Sep 20 23:52:51 (none) kernel: I2O Bus Adapter OSM v$Rev$

Sep 20 23:52:51 (none) kernel: I2O Block Device OSM v1.287

Sep 20 23:52:51 (none) kernel: I2O SCSI Peripheral OSM v1.282

Sep 20 23:52:51 (none) kernel: I2O ProcFS OSM v1.145

Sep 20 23:52:51 (none) kernel: Fusion MPT base driver 3.03.04

Sep 20 23:52:51 (none) kernel: Copyright © 1999-2005 LSI Logic Corporation

Sep 20 23:52:51 (none) kernel: Fusion MPT SPI Host driver 3.03.04

Sep 20 23:52:51 (none) kernel: Fusion MPT FC Host driver 3.03.04

Sep 20 23:52:51 (none) kernel: Fusion MPT SAS Host driver 3.03.04

Sep 20 23:52:51 (none) kernel: usbmon: debugfs is not available

Sep 20 23:52:51 (none) kernel: usbcore: registered new driver hiddev

Sep 20 23:52:51 (none) kernel: usbcore: registered new driver usbhid

Sep 20 23:52:51 (none) kernel: drivers/usb/input/hid-core.c: v2.6:USB HID core driver

Sep 20 23:52:51 (none) kernel: mice: PS/2 mouse device common for all mice

Sep 20 23:52:51 (none) kernel: NET: Registered protocol family 2

Sep 20 23:52:51 (none) kernel: input: AT Translated Set 2 keyboard as /class/input/input0

Sep 20 23:52:51 (none) kernel: TCP: Hash tables configured (established 32768 bind 32768)

Sep 20 23:52:51 (none) kernel: TCP reno registered

Sep 20 23:52:51 (none) kernel: TCP bic registered

Sep 20 23:52:51 (none) kernel: Initializing IPsec netlink socket

Sep 20 23:52:51 (none) kernel: NET: Registered protocol family 1

Sep 20 23:52:51 (none) kernel: NET: Registered protocol family 17

Sep 20 23:52:51 (none) kernel: RAMDISK: Compressed image found at block 0

Sep 20 23:52:51 (none) kernel: Freeing unused kernel memory: 280k freed

Sep 20 23:52:51 (none) kernel: squashfs: version 3.0 (2006/03/15) Phillip Lougher

Sep 20 23:52:51 (none) kernel: bootsplash 3.1.6-2004/03/31: looking for picture...<6> silentjpeg size 56523 bytes,<6>...found (1024x768, 56415 bytes, v3).

Sep 20 23:52:51 (none) kernel: bootsplash: status on console 0 changed to on

Sep 20 23:52:51 (none) kernel: cdrom: hda: mrw address space DMA selected

Sep 20 23:52:51 (none) last message repeated 7 times

Sep 20 23:52:51 (none) kernel: input: ImPS/2 Generic Wheel Mouse as /class/input/input1

Sep 20 23:52:51 (none) kernel: Linux agpgart interface v0.101 © Dave Jones

Sep 20 23:52:51 (none) kernel: NTFS volume version 3.1.

Sep 20 23:52:51 (none) kernel: NTFS volume version 3.1.

Sep 20 23:52:52 (none) kernel: Intel ISA PCIC probe: not found.

Sep 20 23:52:52 (none) kernel: Databook TCIC-2 PCMCIA probe: not found.

Sep 20 23:52:52 (none) logger: /etc/rc.d/rc.hotplug start (entering script)

Sep 20 23:52:53 (none) kernel: shpchp: Standard Hot Plug PCI Controller Driver version: 0.4

Sep 20 23:52:53 (none) kernel: forcedeth.c: Reverse Engineered nForce ethernet driver. Version 0.48.

Sep 20 23:52:53 (none) kernel: ACPI: PCI Interrupt 0000:00:08.0[A] -> Link [LMAC] -> GSI 10 (level, low) -> IRQ 10

Sep 20 23:52:54 (none) kernel: eth0: forcedeth.c: subsystem: 01565:2503 bound to 0000:00:08.0

Sep 20 23:52:54 (none) kernel: ACPI: PCI Interrupt 0000:00:06.1 -> Link [LAZA] -> GSI 11 (level, low) -> IRQ 11

Sep 20 23:52:56 (none) kernel: ACPI: PCI Interrupt 0000:00:02.1 -> Link [LUB2] -> GSI 11 (level, low) -> IRQ 11

Sep 20 23:52:56 (none) kernel: ehci_hcd 0000:00:02.1: EHCI Host Controller

Sep 20 23:52:56 (none) kernel: ehci_hcd 0000:00:02.1: debug port 1

Sep 20 23:52:56 (none) kernel: ehci_hcd 0000:00:02.1: new USB bus registered, assigned bus number 1

Sep 20 23:52:56 (none) kernel: ehci_hcd 0000:00:02.1: irq 11, io mem 0xfe02e000

Sep 20 23:52:56 (none) kernel: ehci_hcd 0000:00:02.1: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004

Sep 20 23:52:56 (none) kernel: hub 1-0:1.0: USB hub found

Sep 20 23:52:56 (none) kernel: hub 1-0:1.0: 10 ports detected

Sep 20 23:52:56 (none) kernel: ACPI: PCI Interrupt 0000:00:02.0[A] -> Link [LUBA] -> GSI 10 (level, low) -> IRQ 10

Sep 20 23:52:56 (none) kernel: ohci_hcd 0000:00:02.0: OHCI Host Controller

Sep 20 23:52:56 (none) kernel: ohci_hcd 0000:00:02.0: new USB bus registered, assigned bus number 2

Sep 20 23:52:56 (none) kernel: ohci_hcd 0000:00:02.0: irq 10, io mem 0xfe02f000

Sep 20 23:52:56 (none) kernel: hub 2-0:1.0: USB hub found

Sep 20 23:52:56 (none) kernel: hub 2-0:1.0: 10 ports detected

Sep 20 23:52:58 (none) kernel: USB Universal Host Controller Interface driver v2.3

Sep 20 23:53:01 (none) logger: /etc/rc.d/rc.hotplug start (exiting script)

Sep 20 23:54:00 (none) kernel: NET: Registered protocol family 10

Sep 20 23:54:00 (none) kernel: lo: Disabled Privacy Extensions

Sep 20 23:54:00 (none) kernel: IPv6 over IPv4 tunneling driver

Sep 21 00:02:49 (none) kernel: usb 1-1: new high speed USB device using ehci_hcd and address 2

Sep 21 00:02:49 (none) kernel: Initializing USB Mass Storage driver...

Sep 21 00:02:49 (none) kernel: scsi6 : SCSI emulation for USB Mass Storage devices

Sep 21 00:02:49 (none) kernel: usbcore: registered new driver usb-storage

Sep 21 00:02:49 (none) kernel: USB Mass Storage support registered.

Sep 21 00:02:54 (none) kernel: Vendor: Kingston Model: DataTraveler 2.0 Rev: PMAP

Sep 21 00:02:54 (none) kernel: Type: Direct-Access ANSI SCSI revision: 00

Sep 21 00:02:56 (none) kernel: SCSI device sdb: 2015232 512-byte hdwr sectors (1032 MB)

Sep 21 00:02:56 (none) kernel: sdb: Write Protect is off

Sep 21 00:02:56 (none) kernel: SCSI device sdb: 2015232 512-byte hdwr sectors (1032 MB)

Sep 21 00:02:56 (none) kernel: sdb: Write Protect is off

Sep 21 00:02:56 (none) kernel: sdb: sdb1

Sep 21 00:02:56 (none) kernel: sd 6:0:0:0: Attached scsi removable disk sdb

[FryShadow 90]

Sep 20 23:53:41 (none) dhcpcd[5301]: timed out waiting for a valid DHCP server response

kalau set static IP bleh ping router tak ? ping others pc boleh ?

dari msg tu mcm ada prob ngan dhcp router tu, tggu yg lain

[athlon_crazy 0]

Sep 21 00:11:01 (none) dhcpcd[10639]: timed out waiting for a valid DHCP server response

Sep 21 00:12:51 (none) dhcpcd[11210]: timed out waiting for a valid DHCP server response

concentrate on both..

[fl1pfl0p 0]

kalau set static IP bleh ping router tak ? ping others pc boleh ?

dari msg tu mcm ada prob ngan dhcp router tu, tggu yg lain

ari tu dah set static ip dah.lepas set static ip kat gui keluar message "kde:Connection established" and gambar dua computer tapi satu computer jer blinking kat tray.pastu try ping router keluar error "host name look up failure".ade satu pc je behind router tak mampu beli banyak2..

[sharuzzaman 1]

kalau dhcpcd tak jalan... cuba guna dhclient lak...

sebab kalau dalam debian, memula dia try dhcpcd... kalau tak dapat IP, dia try lak guna dhclient... biasanya lepas tu dapat la..

[athlon_crazy 0]

ari tu dah set static ip dah.lepas set static ip kat gui keluar message "kde:Connection established" and gambar dua computer tapi satu computer jer blinking kat tray.pastu try ping router keluar error "host name look up failure".ade satu pc je behind router tak mampu beli banyak2..

"host name lookup" macam guna $ nslookup aje...

$ ping normally will result "unknown host" / "destination host unreachable"

cuba ping ip router, klu still x dapat, guna mana2 live-cd untuk ping ip router.

[FryShadow 90]

kalau guna OS lain boleh ping router as normal or other live cd means NIC ko ok, and Backtrack maybe ada prob.

kalau tak boleh ping else ko punye connection maybe ada prob. try gna OS lain k

selamat berjaya

[fl1pfl0p 0]

"host name lookup" macam guna $ nslookup aje...

$ ping normally will result "unknown host" / "destination host unreachable"

cuba ping ip router, klu still x dapat, guna mana2 live-cd untuk ping ip router.

sori la salah information la itu result utk command ifconfig,result ping mmg "Destination host unreachable".pastu aku jugak try telnet router tu, kuar error "No route to host".juga dah try live cd lain knoppix 5.1.0 dan ubuntu edgy dua2 dapat ping router,dua2 pun automatically detect internet masuk je dah boleh terus surf.Backtrack ni je problem mungkin sbb dier utk kegunaan l337 je kot.

kalau dhcpcd tak jalan... cuba guna dhclient lak...

sebab kalau dalam debian, memula dia try dhcpcd... kalau tak dapat IP, dia try lak guna dhclient... biasanya lepas tu dapat la..

ok lepas buat command ifconfig utk set ip ,netmask, gateway aku terus wat dhclient .Output dier -->

Internet Systems Consortium DHCP Client v3.03

Copyright 2004-2005 Internet System Consortium.

All rights reserved.

For info, please visit http://www.isc.org/products/DHCP

Listening on Socket/eth0

Sending on Socket/eth0

DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 4

DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 8

DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 17

DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 8

DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 13

DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 11

No DHCPOFFERS received.

No working leases inpersistent databases-sleeping

Nampakneye router aku mmg degil la tak nak respond. ape la problem nye:wacko:

p/s:aku ade try backtrack live cd ni tadi kat Virtual PC 2007 ,boleh pulak masuk internet maybe sbb dier amik xp punye config

[FryShadow 90]

moral of the story takyah la gna backtrack hehe...

[fl1pfl0p 0]

moral of the story takyah la gna backtrack hehe...

mula2 saje je nak try backtrack ni,aku nak try sume linux flavour .naktengok mane yg lagi best ,lagi lawo ,laju.backtrack ni laju loading pastu ade byk tool2 yg aku nk explore.saje je nak cari pengalaman gune linux,kalo boleh nak sume bende boleh wat ngan linux ni mcm surfing , word ,dengar lagu.bile aku dah pakar nanti tak payah la gune windows lagi..

aku masih berharap lagi boleh dpt internet kat backtrack ni..bile tahu ape punce sbnrnye tak dpt connect boleh tambah knowledge aku..

Edited September 21, 2007 by fl1pfl0p

[kaizen 0]

Backtrack....

aku guna live cd back track 2

,, ok je,, terus dapat internet...tk perlu nk configure papepun..

back track bagus nk try blajar hacking2 nih... aku pakai vmware 6 configure guna bridge or NAT.. pun ok.. still je dpt internet.. tnpa perlu pape configuration.. janji dhcp je la..

aku pun sama suka explore linux...

antara terbest mintlinux KDE...lawo lak tuh..

lg ok dr nk guna kubuntu...

member aku pun jenis mcm aku suka explore linux interface... bila aku suruh je guna mintlinux kde..

terus je nk guna terus.. windows tknak pakai da..

klu nk pure security... guna suse linux.. cun n more security....

linux takde virus... ni yang plg best..

[FryShadow 90]

tak sure la ko gna backtrack versi brapa.. tp yg latest backtrack 2 ler . mungkin bleh consider gna vmware kalau nk gna sgt

[fl1pfl0p 0]

aku gune backtrack 1.0 final.tapi skang nak gi download backtrack 2 plak

[sharuzzaman 1]

klu nk pure security... guna suse linux.. cun n more security....

tak boleh assume macam ni... dalam mana-mana OS, termasuk juga Linux dan mana-mana distro... aku boleh katakan tak der security... sebab security adalah proses, bukan produk...

kalau aku guna Debian, atau Fedora, atau Slackware, atau Gentoo, pun boleh secure gak, kalau aku tahu camner nak secure kan...

tapi kalau aku guna Suse, pun boleh jadi tak secure gak... mungkin boleh kena cr.ack jugak... kalau aku tak tahu camner aku nak secure kan...

so, belajar macam mana proses nak secure kan sesuatu OS tu... bukan hanya berharap distro tu untuk automatik jadi secure...

OpenBSD yang orang kata secure pun still ada security hole... walaupun tak selalu...

Edited September 26, 2007 by sharuzzaman